Jeremy Carr

Utilizing my bitcoin network along with my social media presence, (youtube platform) I have gained visibility of a growing audience to which drives my cryptocurrency consulting and mining support.

Owner/Operator of a large bitcoin mining center; successfully designed, built, implemented a 24+ PH Bitcoin mining Center. This was a huge undertaking in which I was the Project Manager, Design, and implementation of the IT infrastructure. Also designed the cooling system which was a cost savings of over a hundred thousand dollars by researching and sourcing straight from the factory for our equipment. I worked with a subcontractor to design specialized racks designed to fit the proper number of miners, PSU's, and trays for hiding the wires and cables. I have gained a lot of experience and insight from this project. I would currently be open to another opportunity with the right circumstances.

• Tasked with managing the service order on both the local network (CO to Prem) and National network (CO to Cloud). Worked with Field Technicians on customer prem install and test of EoC, EoT1, or EoFiber. Including provisioning of Adtran Netvanta at the Customer Prem and Adtran TA5000 in the CO.
• Worked in a NOC environment in switch services, national accounts, DS1 Provisioning, CIA, customers initiated grooms (the cut group), and Ethernet provisioning.
• The provision, Test, and Turn-Up of Sonet Systems, OC192, OC48, OC12, OC3, DS3, DS1, DS0, Primary Rate ISDN, Advanced Trunks, Basic DID Trunks, Digital and Analog Circuits.
• Remote testing, provisioning and verifying of ADC Soneplex and Adtran HDSL systems.
• Remote testing, provisioning of the NextLevel system.
• Remote provisioning and mapping of Fujitsu FLM150, FLM600, FLM2400, Flashwave 4500, Flashwave 4100, Nortel, Flash 192, Lucent Lambda Unite, NEC and Cisco 15454 muxes.
• Remote provisioning of Tellabs Titan 5500 DACS, AT&T Dacs IV, AT&T Dacs II, and Alcatel Dacs using TL1 command interface.
• Extensively utilize NMA (TL1 interface), Intas, TEMs, View-1, Preside, Cisco Transport Controller, and other systems to perform the remote testing and provisioning functions.
• Experience and knowledge with following test equipment: Optical TDR, TBERD 310/2310, Optical Fault Locator, Optical Fiber Identifier, Optical Scope, optical and electrical power meters.
• Verified and made programming changes to Switch Translations in the Nortel DMS100, DMS10, Lucent 5ESS, Lucent 1AESS, and Ericsson AXE Central Office Switches.
• Work daily within Qwest’s internal programs to include WFA-C, WFA-DO, WFA-DI and Tirks
• Troubleshooting and repair of any problems with new circuits by interfacing with Central Office Technicians, Customer Data Technicians, Circuit Designers, and Order Originators.

• Prioritized duties, as well as instructed and guided junior technicians in the areas of safety, maintenance, troubleshooting, and repair.
• Managed inventory and performed in-house customer service.
• Installed, maintained, troubleshot, and operated aircraft Communication and Navigation Equipment, such as IFF, TCAS, VOT/ILS Receivers, FM Marine Band Radio, UHF Radio, Navigation/Search Radar, GPS, Intercommunication System, and Radar Altimeters.
• Utilized electronic Test equipment such as TDR’s, Oscilloscopes, Communication analyzers, and Multimeters.
• Served onboard the HC-130 as the Navigator, ensuring the accuracy of the flight plan, maintaining the navigation flight log, and supported pilots on airfield approaches.

• Installed, maintained, and troubleshot HF-80 high-powered transmitters and receivers down to circuit card and component level.
• Performed preventive maintenance, as well as troubleshot and repaired HF antennas.
• Qualified to climb antenna towers up to 200ft.
• Ensured and maintained communication station equipment by completing hourly inspections and documenting the results.
• Assisted the receiver site in synchronized troubleshooting and testing of the HF system. Fireman onboard the USCGC Ironwood (Ships Engineering, Power and Propulsion Systems) at U.S.

Basic Fireman duties - Assisted senior Engineroom Machinest Mates in both inport and underway main propulsion system onboard a 180 ft ATON Coast Guard Cutter Ironwood. Kodiak AK.

8 weeks of U.S. Coast Guard indoctrination (Boot Camp)